Motolyser User Suggestions
Do you have some general ideas about the Motolyser? Let us know where we’re not up to scratch and how we can make things better. Or tell us what you need, to get more out of your brushless motor.
If you have a problem, this is not the place to get it fixed! Please use our helpdesk for that, this is for positive suggestions on how to direct the future of Motolyser development for all of us.
21 results found
-
4 pole support
I'm slowly having less use for my motorlyser due to it not functioning with 4 pole. Can 4 pole support be added for us drag racers?
11 votes -
6 votes
-
Asymmetry not reading correctly
After upgrading my Motolyser v1 to 3.0 all my asymmetry values are way off. Reading 18-19 on any rotor I put in.
1 vote -
Ability to test at higher amp draws.
Motolyser will not run motors at some of the higher timing ranges / higher amps that we currently race at.
45 votes -
Watts readout
Add a Watts tab to the test info page
18 votesThis is a realizable idea. We need to look into where to place the value in the menu.
-
Hello , How can i use the motolyser printer ?
How can i use the motolyser printer ?
in bluetooth26 votes -
SENSOR ALIGNMENT TOOL OR TEMPLATE-THIN LEXAN OR MATERIAL THAT HAS SENSOR CUTOUTS IN A CIRCLE TO ALIGN EASIER.
motorlyser has the test feature so why not provide a sensor tool to align these tiny sensors-that the factor doesnt take the time to align-and provide a tool with motolyser to do this when tunning motor
103 votes -
Ability To Put Motor Under A Load..
Design The Motolyser To Have The Ability To Place The Motor Under A Load Similar To The Fantom And Turbo Dyno. The Motolyser Will Be Able To Give Torque And Efficiency Readouts.
110 votes -
data save
data from each motor saved to compare against other motors tested along with trackside features like track size gearing rollouts from motor data thats been already proven on track and key in results that will be used in other motor selection for better performance.
9 votes -
Add the detail that is calculating the Magnetic Asymmetry
Since the device is able to provide a "score" of Magnetic Asymmetry, it should be possible to display the strength of the Magnetic field on the device as well.
75 votes -
PC driven test. Step X percent motor every Y seconds. Log results in simple csv format for graphing (or graph in the tool)
similar to allow data to be stored idea below, but the parameters driven by software. At the moment I have to take pictures or write values down. leaves the motor running longer than it needs to.
118 votes -
Allow data to be stored about the motor on the pc. print out motor facts and allow the user to add information:sensor, timing, shim, rotor
A small database that takes
Motor
Date of test
Timing
Sensor board
RotorFront the user and allows the data from the test session to be included
Print a PDF "facts" sheet.
135 votes -
Please have a menu that indicates KV changes corresponding to timing changes.
It is very useful to know the effect that timing increase/decrease has on motor KV, both for racers as well as for race control.
21 votes -
Maximum timing deviation figure
Add a maximum timing deviation figure in the timing advance menu. Faster to see if the sensor board is smooth or not.
For example: 25.5 23.0 21.5 = 4.035 votes -
Release an API
Then I can program my own tests/tools and share with the community.
9 votes -
Include a settings menu
Introduce a separate menu for system specific settings. Please comment on what settings you feel are most critical.
20 votesThis is a Planed feature. We just need to decide on some basic settings to start with. Please provide us with thoughts about this.
-
7 votes
This is something that will be added once a settings menu is created. There need to be a simple way without overhead to change this setting back and forth
-
LARGER DISPLAY WITH LARGER LETTERING
for us OLDER rc hobbyists a LARGER DISPLAY WITH LARGER TYPESET/LETTERING would be wonderful!!
8 votes -
55 votes
-
Need to be able to use with hotter motors
I would like the Motolyser to be used with lower turn motors... When I try to use the motorlyser with my 2.5-3.0 turn motors I get error message.. I would like to use it with these motors....
22 votes
- Don't see your idea?